Pairing a card terminal
Last updated: October 7, 2026
This guide shows a venue owner or manager how to connect a card payment terminal (an EFTPOS pinpad) to the DineHopper till, so card payments taken at the till go straight to the terminal and the order closes itself when the payment is approved. DineHopper connects to terminals through Linkly Cloud.
On this page
Before you start
You will need three things.
- A terminal that has been set up for Linkly Cloud. Your bank or Linkly arranges this. If the terminal is currently connected to another till system over a cable or the local network, it has to be moved to Linkly Cloud first. A terminal can be paired to only one till system at a time: pairing it to DineHopper disconnects it from the other one.
- Your Linkly Cloud lane username and password. Linkly or your bank supplies these when the terminal is set up for Cloud. They are not your DineHopper login.
- A DineHopper owner or manager login, and an internet connection on the till and on the terminal.
Step 1. Get a pairing code from the terminal
- On the terminal, press FUNC, type 8880, then press OK (Enter).
- The terminal shows a pairing code. Leave it on screen.
Pairing codes expire after a few minutes, so go straight to Step 2. If the code runs out, repeat this step to get a new one. Some terminal models use a different key sequence; if FUNC 8880 does nothing on yours, ask your bank or Linkly for the Cloud pairing steps for your model.
Step 2. Pair it in DineHopper
- Sign in to DineHopper and open Configure, then Payment terminals.
- In the form under the terminals table, fill in:
- Register name: the name of the till register this terminal belongs to, written exactly as the till shows it. A single-till venue uses Register 1. A card machine for the self-order kiosk uses Kiosk 1.
- Provider: Linkly.
- Lane username and Lane password: the Linkly Cloud details from the list above.
- Environment: Production to take real cards. Choose Sandbox only for testing with a test terminal, because Sandbox never charges real cards.
- Pairing code: the code now showing on the terminal.
- Press Pair terminal.
- The terminal now appears in the Payment terminals table with the status Active. DineHopper stores the connection securely and you will not need to enter the lane password again.
If your venue has more than one register with its own terminal, repeat Steps 1 and 2 for each one using that register's own label.
Step 3. Take a test payment
- On the till, make a small order and press Take payment, then EFTPOS.
- The till shows Waiting for the terminal and the terminal asks for a card.
- Tap, insert or swipe a card. When the terminal approves it, the till marks the order paid and the order closes.
If you want to prove it without keeping the money, refund the order afterwards from the Orders list. The refund goes back to the same card through the terminal.
If something goes wrong
- Pairing fails. The three usual causes are an expired pairing code (get a new one), a wrong lane username or password, and the wrong Environment. The message under the form says which one applies.
- The till says no EFTPOS terminal is paired. The Register name used when pairing does not match the register you are selling from. Pair again using the name the till uses, normally Register 1.
- The till says it could not reach the terminal. Check the terminal is switched on and online, then try the payment again. A short code in brackets after the message helps support find the cause.
- The till says a card attempt never reported back. DineHopper will not start a second card payment while an earlier one is unknown, because the guest may already have been charged. Check the terminal or its slip, then answer Was the card payment taken? on the till. If the terminal can still be asked, DineHopper asks it first and uses its answer.
- Power cut or network drop in the middle of a payment. When the till opens again it automatically asks the terminal what happened to any payment that was in progress, updates the order, and prints a slip showing the result. You can also check at any time with More, then Check last card payment.
Still stuck? Email support@dinehopper.com with your venue name and the register label.
Setting a backup terminal
If you have a second terminal, it can take over when the first one cannot take a card.
- Pair both terminals as above, each with its own register label.
- Open Configure, then Payment terminals. In the Backs up column, choose the register each terminal backs up.
- The change saves by itself and shows Saved.
If the register's own terminal is offline, busy or not paired, the card sale moves to the backup and the till tells the cashier which terminal the guest should use. If the first terminal simply does not answer, DineHopper does not move the sale: the card may still be going through. It waits until that payment is settled, so a guest is never charged twice. Every move is recorded in the activity log.
Moving or re-pairing a terminal
To disconnect a terminal, open Configure, then Payment terminals, and press Unpair beside the register. DineHopper deletes the stored connection and that register stops taking card payments until it is paired again. To pair it again, or to pair a replacement terminal, start from Step 1 with a fresh pairing code. Re-pairing a register keeps its identity, so reports and history carry on without a break.